2016 Chevrolet Volt Keyless Entry Remote Fob Smart Key Programming Instructions
Share
2016 Chevrolet Volt Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:A.
Procedure with at least one programmed transmitter available.
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
NOTE: Switch the ignition to the OFF position.
2. Insert the key blade into the door lock outside of the driver's door (pull the metal key blade out of the transmitter by pressing the release button located in the front of the key, you can use the blade from the working transmitter).
3. Turn the key blade in the door lock to the unlock position 5 times within 10 seconds. Driver's information center DIC will display READY FOR REMOTE #2, 3, 4, ETC.
4. Place the new transmitter into the center console transmitter pocket (open the storage area and remove the rubber mat to access the transmitter pocket spot).
5. Press and hold the ignition POWER button for 2 seconds. When the new transmitter is programmed, the DIC will display that it is ready to program the next transmitter.
6. Remove the new transmitter from the transmitter pocket and press UNLOCK or LOCK button on the remote.
Repeat steps 4, 5, and 6 for each additional transmitter.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
Test each of the remotes to make sure they are working.
B.
Programming without Two Working Smart Keys:
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete.
DIY programming is not available in Canada.
Before you start programming, make sure that the vehicle is off and all transmitters are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
Please Note:
if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
2016 Chevrolet Volt Transponder Key Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:A.
Procedure with at least one programmed transmitter available.
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
NOTE: Switch the ignition to the OFF position.
2. Insert the key blade into the door lock outside of the driver's door (pull the metal key blade out of the transmitter by pressing the release button located in the front of the key, you can use the blade from the working transmitter).
3. Turn the key blade in the door lock to the unlock position 5 times within 10 seconds. Driver's information center DIC will display READY FOR REMOTE #2, 3, 4, ETC.
4. Place the new transmitter into the center console transmitter pocket (open the storage area and remove the rubber mat to access the transmitter pocket spot).
5. Press and hold the ignition POWER button for 2 seconds. When the new transmitter is programmed, the DIC will display that it is ready to program the next transmitter.
6. Remove the new transmitter from the transmitter pocket and press UNLOCK or LOCK button on the remote.
Repeat steps 4, 5, and 6 for each additional transmitter.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
Test each of the remotes to make sure they are working.
B.
Programming without Two Working Smart Keys:
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete.
DIY programming is not available in Canada.
Before you start programming, make sure that the vehicle is off and all transmitters are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner's manual. Up to 8 smart keys can be programmed to a vehicle.
Please Note:
if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
Use our Locksmith Search if you need professional help.